歡迎訪問東莞市高鼎檢測設備配件有限公司 免費服務 熱線:400-8755521
 
 
News
Contact Us

Add: No.9, Jinghai East Road, Shatou,Chang’an Town, Dongguan, Guangdong.
Tel:+86-0769-85385589 85381189
Phone:13480439007
Fax:+86-0769-85385989
E-mail:jenny@goodingjp.com
SKYPE number:jennyliu6666
News ? Industry News
What's wrong with CNC machining accuracy?
Time:【2019-10-26】 Browse【2720】 【Print】【Back
1. Workpiece size is accurate, surface finish is poor fault reasons: tool tip damage, not sharp; machine tool resonance, placement is not stable; machine tool crawling phenomenon; poor processing technology.
Solution: If the tool is not sharp after wear or damage, grind the tool again or choose a better tool to re-align the tool; if the machine tool is resonant or placed unsteadily, adjust the level, lay the foundation and fix the tool smoothly; the reason of mechanical crawling is that the trawler guide rail is worn badly, the ball screw is worn or loosened, the machine tool should be maintained carefully, and the wire should be cleaned after going to and going to work, and timely moistened. Lubricating oil to reduce friction; select suitable cooling fluid for workpiece processing, in order to meet the processing requirements of other processes, try to choose a higher spindle speed.

2. Workpiece taper size head failure causes: machine tool placement level is not adjusted well, one high one low, resulting in placement instability; turning long axis, the contribution material is relatively hard, the cutter knife deep, resulting in knife-letting phenomenon; tailstock pin and spindle are not centralized.
Solution: Use level instrument to adjust the level of machine tool, lay a solid foundation, fix the machine tool well and improve its toughness; choose reasonable technology and appropriate cutting feed to avoid tool force concession; adjust tailstock.

3. The driver phase lamp is normal, but the small fault causes when the workpiece size is large: the machine tool trawler runs at a high speed for a long time, which results in the wear of the screw and bearing; the repetitive positioning accuracy of the tool holder produces deviation in the long-term use; the trawler can accurately return to the processing starting point every time, but the size of the workpiece is still changing. This phenomenon is generally caused by the spindle. The high speed rotation of the spindle causes serious wear of the bearing, which leads to the change of processing size.
Solution: Depend on the bottom of the tool holder with the dial indicator, and edit a fixed cycle program through the system to check the repetitive positioning accuracy of the trailer, adjust the clearance of the screw and replace the bearing; check the repetitive positioning accuracy of the tool holder with dial indicator, adjust the machine or replace the tool holder; check whether the workpiece is accurately returned to the starting point of the program after processing with dial indicator, and if possible, repair the spindle. Change bearings.
4. The size of the workpiece differs from the actual size by several millimeters, or there is a great change in the axis of the workpiece. The reason for the failure is that the speed of rapid positioning is too fast to respond to the drive and motor; the drag plate screw and bearing of the machine are too tightly jammed after a long period of friction loss; the tool holder is too loose and the lock is not tightened after tool change; the editing procedure is wrong, and the system ends without the head and tail responding or canceling the tool repair; Error setting of electronic gear ratio or step angle.
Solution: If the speed of quick positioning is too fast, the GO speed will be adjusted appropriately, and the speed of cutting acceleration and deceleration and time will make the driver and motor work normally at the rated operating frequency; if the tractor and screw crane bearings become too tight after machine tool wear, they must be readjusted and repaired; if the tool holder is too loose after tool change, the reverse time of the tool holder will be checked and the vortices inside the tool holder will be checked. Whether the gear and worm are worn, whether the clearance is too large, whether the installation is too loose, etc. If it is caused by the program reasons, the program must be modified, according to the requirements of workpiece drawings, improve, select reasonable processing technology, write the correct program according to the instructions of the manual; if the size deviation is too large, check whether the parameters of the system are set reasonably, especially the electronic gear and the step angle, etc. Whether the parameters are destroyed or not can be measured by a dial indicator.

Copyright ©  Dongguan Yuding Industry Limited. 粵ICP備2023120264號


高鼎中文站:www.aabbcc15e.com
主站蜘蛛池模板: 国产午夜一区二区在线观看| 好男人资源在线手机免费| 亚洲国产综合专区在线电影 | 亚洲AV网址在线观看| 欧美高清视频一区| 制服丝袜日韩欧美| 色多多www视频在线观看免费| 国产欧美日韩一区二区三区在线| 97久久精品无码一区二区天美| 岛国免费v片在线观看完整版| 久久久久久久久久久久久久久| 最好看的2018中文字幕国语免费 | 中文字幕免费在线看线人| 日韩欧美第一页| 亚洲人成人网站在线观看 | 国产激情久久久久影院小草 | 日韩精品一卡二卡三卡四卡2021| 亚洲国产欧美一区| 波多野结衣中文字幕一区二区三区 | 成人在线观看不卡| 久久人人爽爽爽人久久久| 欧洲美熟女乱又伦av影片| 亚洲日韩av无码中文| 波多野结衣无限| 免费无码国产V片在线观看| 美国大片免费收看| 国产AV人人夜夜澡人人爽麻豆| 韩国太太的告白韩国电影| 国产成人精品视频福利app| 福利视频导航网站| 国产精品无码久久av不卡| 91成人精品视频| 国自产拍91大神精品| aaa毛片免费观看| 女人是男人的未来视频| 一级毛片特级毛片黄毛片| 成人欧美一区二区三区的电影| 久久久久久亚洲av无码专区| 日本精品一卡二卡≡卡四卡| 久久精品夜色国产亚洲av| 最近中文字幕完整在线电影|